how to fit led bathroom mirror | JIAJIE

how to fit led bathroom mirror

Our led lighted bathroom mirror are designed to be easily attached to the wall using four anchor type screws (all fittings included). In most cases, the steel base of the mirror is attached to the wall using the four anchor type screws. The bathroom mirror led lights power source comes directly from your 110V mains power supply (just like a light or ceiling fan does). The 110V wiring will come through the hole provided in the center of the steel base and attaches to the correct wires within the steel base as shown in the Wiring Details section below.

The mirror is hard wired and requires 110V cabling that is directly inserted in to the back of the mirror’s steel back plate. If you don’t have this cabling available and are unsure of how to do this type of electrical work, we highly recommend using a licensed professional to assist you with installing your LED backlit mirror. The 110V mains supply cabling (Black, White and Copper for ground) simply connects to the appropriate wires located inside the mirror using wire nuts or electrical block connecter as applicable to the model.

Once the 110V wiring is correctly attached you will then need to attach the quick plugs which allow the De-Mister to work. Once all the necessary connections have been safely made, your led bathroom mirror lighting then simply slots safely on to the steel base which is attached to the wall. Depending on the model of mirror you have purchased, there may also be screws that are used to attach the mirror to the steel base. These are used to further safeguard your mirror and anchor it to the steel base.

Installation steps

  1. Carefully remove your bathroom mirror with led lights from packaging.
  2. Place the Bathroom mirror with lighting face down on the floor to measure for your hanging points.
  3. Mark the hanging measurements out on wall surface and drill with a 10mm drill bit.
  4.  Hammer wall plugs into drill holes and screw-in the supplied screws.
  5. Unscrew the four screws from the power supply unit.
  6. Once power unit is taken off, insert mains cable into rubber grommet.
  7.  When fed through the grommet, connect electrical wiring.
  8. Fasten wires down with a flat head screw driver.
  9. Once main cable is connected, reconnect power supply unit to its brackets.
  10. Screw in original four screws to fasten power supply unit in place.
  11.  Wave your hand by the sensor to ensure mirror lights turn on.
  12.  Hang mirror on wall screws to complete your installation.

IMPORTANT!

Always shut off power to the circuit beforestarting installation work. 

electrical installation work may onlybe carried out by a authorised electrical contractor. Contact your local electricity authority for advice.

INSTALLATION IN BATHROOMS

The installation shall be carried out by an authorised electrical contractor.

The luminaire must be permanently installed in the electric system and placed in the correct zone.

Care and Cleaning Instructions for Mirrors

CLEANER

The best and safest cleaner for a mirror is clean, warm water used with a soft cloth. Be careful not to allow the edges of the mirror to get or remain wet over a period of time.
If using a commercial glass or mirror cleaner, be sure to use a standard brand of mirror cleaner that does not contain ammonia or vinegar. Do not use Windex.

APPLICATION

Never spray any cleaner directly on to a mirror. Instead apply the cleaner to a soft cloth and then wipe the mirror.

CLOTHS

Always use soft, grit-free cloths when cleaning a mirror to reduce chances of scratching the surface.

FINISH

Be sure to dry all joints and edges thoroughly to be certain no commercial cleaner comes in contact with the edge and backing.

Bathroom Mirrors with LED Lights | Round LED Bathroom Mirror

http://www.jiajiebathmirror.com/round-oval-smart-tempered-bathroom-mirror-led.html

Round Oval Smart Tempered Bathroom Mirror LED

http://www.jiajiebathmirror.com/round-moisture-proof-sauna-room-waterproof-mirror.html

Round Moisture proof Sauna Room Waterproof Mirror

http://www.jiajiebathmirror.com/round-electronic-anti-fog-white-yellor-blue-light-led-backlit-wall-mounted-diameter-24-27-32-touch-screen-bathroom-mirror-led.html

ODM and OEM Round LED Bathroom Mirror

http://www.jiajiebathmirror.com/round-vanity-switchdigital-clocktemperature-displaydemister-bathroom-mirror.html

Round Vanity Switch+Digital Clock+Temperature Display+Demister Bathroom Mirror

/products/round-led-bathroom-mirror/

Round Electronic Anti-fog White Yellor Blue Light LED Backlit Wall-Mounted diameter 24″ 27″ 32″ Touch Screen Bathroom Mirror LED

LED bathroom mirror price

Huizhou Jiajie Hardware Electronics Co., Ltd. is ODM and OEM smart bathroom mirror factory. It with auto field china top 10 rearview mirror factory and individual hardware and plastic factory.

To Order fill inquiry form with Book/Product Name & your place Postal Pin Code number or e-mail atada_lee@jiajiebathmirror.com, we will mail/call back to help you for easy buy!

http://www.jiajiebathmirror.com/about-us/

 


Post time: Nov-19-2018
WhatsApp Online Chat !